Primer Pocket Uniformer 21st Century
Depth Adjustable Primer Pocket Uniformer with Carbide Cutter
Calibrated .001 GRAD.
Easy set + or - .0002 and maintain depth
Uniforms large and small primer pockets, simply switch ends on the precision ground carbide cutter.
When sizing a fired case, pulling the expander button through the case can present a problem because residual deposits left from firing can create friction when the expander is withdrawn. In a worst case scenario, that friction can cause distortion or stretching of the case neck. Properly lubricating the inside diameter of your case necks is the answer, but oils are not recommended because of the possibility of gunpowder contamination. The Forster Case Graphiter is constructed of tough, impact resistant plastic and the base is drilled to permit permanent mounting to a loading bench. Three brushes are mounted in the base. They accommodate all calibers from .22 to .35. The Case Graphiter is supplied with adequate white “motor mica” to process 2000-3000 cases. By moving the case neck up and down on the correct graphite-covered brush, the I.D. of the neck can be cleaned and lubricated at the same time. A cover is included to prevent dust and grit from contaminating the graphite (motor mica).
The Hornady One-Shot Case Lube is the most popular case and tool lube on the market. The One-Shot Case Lube is clean, non-sticky, quick and easy to use, and the non-petroleum wax will not contaminate powder or primers. The aerosol spray can allows you to lube an entire block of cases in one shot, which is great when loading large quantities of ammunition.
Material: Aerosol non-petroleum wax
Quantity: 5 oz
Container: Metal Can
All Aerosols are PICK UP ONLY
The Hornady Impact Bullet Puller uses inertia to quickly pull bullets from cartridges up to 45 caliber without damaging the brass or projectile. By tapping the bullet on a wood surface, the bullet will be released and captured in the hollow head for reuse or disposal.e
Unlike other bullet pullers, the Hornady model features a durable aluminium core as opposed to plastic.
$25.00Assists in making your primer pocket depth uniform so loads ignite the same each time. Uniform your brass to achieve accuracy.
KM Shooting's precision Primer Pocket Correction Tool cuts to a predetermined depth using carbide cutters, and now comes with an improved drive shank that will lock into your cordless screw driver chuck. Alternatively you can purchase the KM Tool Handle for manual operation.
NOTE: Do not attempt to adjust setting unless you possess the tool to make precision measurements.
One compact, double-ended storage tool
Lyman's Unique New Case Prep Multi-Tool provides the reloader with all the essential Case Prep Accessories in one compact, double-ended storage tool. Unique handle unthreads in the middle to store all parts. Both ends of the handle are threaded to allow two heads to be mounted simultaneously.
Case Saver: Primer Pocket Swage Large Rifle Mounting Solutions Plus
Use this tool as it is intended and it will pay for itslef by reclaiming brass that will no longer hold a primer.
The Case Saver is intended only for cases which have been reloaded to the point where the primer pocket has worn from continual use and cleaning to where it will no longer function. The Case Saver will lengthen the life of these cases.
Here is how it works:
1. The case is placed over the SUPPORT STAND.
2. The Guide Pin goes through the flash hole in the case and into the Guide Hole in the top of the SUPPORT STAND.
3. Rap the punch LIGHTLY until the primer pocket grips the PUNCH. This indicates the primer pocket diameter has been sufficiently reduced to allow a primer to once again be held firmly in the case.
4. This process can be repeated as often as the primer becomes loose greatly extending the life of the case - See more at: http://www.mountsplus.com/mm5/merchant.mvc?Store_Code=MSP&Screen=PROD&Product_code=PPS-LG1-1PA#sthash.Z9biw3M2.dpuf
Now you can re-swage worn primer pockets in your best shooting cases! Now your best shot will no longer meet with case failure if reloaded. Now the Case Saver can re-swage pocket primers by forming a searing seal in the primer pocket. Easy to use kit includes support stand and punch with guide pun. Fits .30 cal. and above.
Here's How it Works:
The Ultimate Model Kinetic Bullet Puller by Quinetics. The most Energy-Efficient reloading tool available. For all popular rifle, pistol, rim or rimless center fire cartridges. Not for use with rim fire cartridges or explosive projectile ammunition.
Chuck Assembly makes the difference. The tool's specially engineered chuck assembly evenly grips and holds case without damage to either cannelure or rim of case. 1/4 turn of the chuck and your ready to go. 1/4 turn of the chuck and your done. No need to unscrew the chuck to load the bullet or remove the cartridge.
Made in the U.S.A
The RCBS Collet bullet puller is an excellent tool designed to help reloaders dismantle loaded ammunition to save valuable components.
These collets are designed to easily pull out jacketed bullets without damaging them and will only work with the standard RCBS Collet Bullet Puller. They are not compatible with the larger collet bullet puller designed to work in presses with 1-14 threads.
The RCBS Case Neck Brush is designed to help reloaders clean dirt and powder residue from the inside of case necks while at the same time applying lubrication to ease the amount of force required during case neck expansion during the resizing process.
22 to 25 cal
270 to 30 cal
35 to 45 cal
$11.50The case trimmer pilots designed with a taper to guide pilot into the case mouth and guides cutting blades to prevent deformation. Available from .17-caliber to .45-caliber pistol and rifle to .500-caliber.
$165.00The RCBS® Hand Case Neck Turner is designed to peel brass from the outside of a case neck to a consistent thickness, which is important because most commercially available brass has variances in neck thickness. This leads to case neck concentricity and bullet run-out issues. Truing up the case neck produces more consistent and accurate hand loaded ammunition. The cutter portion uses caliber specific pilot/mandrels (sold separately) to guide the case neck. The cutter design can zero the cutter to the pilot/mandrel and then use the micrometer adjustment to dial the desired case neck thickness in .0005-inch increments. The cutter can also be set for right or left handed use.
Handle RCBSThe RCBS Accessory Handle-2 is a great tool to use to provide any reloader a secure "no roll" grip while cleaning and uniforming primer pockets with RCBS primer pocket tools.
Fits: Interchangeable with any RCBS primer cleaning part, also fits RCBS flash hole deburring tool replacement rod and cutter
Function: Large ergonomic handle to hold onto
Notes: Handle is designed to provide a secure grip
The RCBS Pow'r Pull Impact Bullet Puller features a solid one piece body, innovative 3-jaw chuck that firmly grips the case rim. Just tap it on a solid surface as you would a hammer, and the powder and bullet drop into the main chamber for re-use. A soft cushion prevents any damage to bullet. Works with most centerfire cartridges from the 5.7x28mm FN and 22 Hornet up through the Winchester Short Magnum and Remington Ultra Magnum family of cartridges.
Type: Impact Bullet Puller
Function: Separate Bullet from Case to reclaim bullet, powder and brass
Color: Transparent Green
Material: Polymer with Aluminum Chuck Assembly
The RCBS Primer Pocket Brush is a great tool reloaders can use in removing the residue from primer pockets making them cleaner. Brushes are made from stainless steel bristles and are made to fit the RCBS Accessory Handle (product # 477-820) sold separately.
Function: Brush residue from inside of primer pockets
Material: Stainless Steel Bristles
Reduce the work of the case preparation by using the RCBS Trim Mate Case Prep Center. Five gear-driven rotating heads turn the tasks of chamfering, deburring, primer pocket cleaning, military crimp removal, and flash hole deburring into a much easier job. The tough, high torque motor does all the work, letting you move quickly from station to station. Great companion tool for trimming at the same time. There are two stationary positions for case neck brushes or other accessories and a cupped area for holding dry neck lube. The case Prep Center includes large and small primer pocket brushes, inside chamfering and outside deburring tools, medium and small case neck brushes, and a packet of dryneck lube.
The most popular way to properly lubricate cases for resizing and case forming. The bottom side of the pad includes non-skid feet so it won’t skate all over your bench when you a re using it.
The Redding Case Neck Concentricity Gage is a great tool for reloaders to use to sort their brass by thickness and uniformity of case necks. Many of today's top competitive target shooters measure and sort their brass for consistency and uniformity trying to get everything with their ammunition to be the exact same. Taking the time to do this not only helps to reduce any variations but it also gives the shooter the piece of mind to know that their reloaded ammunition is the best it can be.
$57.50The Redding Primer Pocket Uniformer Tool is designed to cut primer pockets to a uniform depthand square them up with the case head. This helps to increase shot to shot consistency to help create the most accurate ammunition possible.
Trimmer Kwick-Trim Case Hand Trimmer
The Kwick Case Trimmer differs from other trimmers in that it indexes from the datum of the cartridge case shoulder in the same manner as a headspace gauge. This eliminates the need for both shellholders, pilots, and it speeds up the trimming process!
Fits: L.E. Wilson Case Trimmers/Whidden Gunworks Meplat Trimmer
Function: Caliber Specific Caliber Sleeves hold bullets square to the cutter
Notes: Cutter can also be used to trim brass
Constructed from highly durable stainless steel, the Wilson package contains: